Kelvinator JT4BE048KA Installation Guide download pdf (Page 8)

Short Cycle Protection

1. Set the thermostat system mode to COOL. Observe the

temperature setting of the thermostat and gradually raise

the set-point temperature until the unit de-energizes.

2. Immediately lower the set point temperature of the

thermostat to its original setting and verify that the

indoor blower is energized and outdoor unit remains

de-energized.

3. After approximately 5 minutes, verify the outdoor unit

energizes and the temperature of the discharge air is

cooler than the room temperature.

System Cooling

1. Set the thermostat’s system mode to COOL and the

fan mode to AUTO. Gradually lower the thermostat

temperature setpoint below room temperature and

verify the outdoor unit and indoor blower energize.

2. Verify blower wheel is spinning in direction indicated by

arrow. Feel the air being circulated by the indoor blower

and verify that it is cooler than ambient temperature.

Listen for any unusual noises. If unusual sounds occur,

determine the source of the noise and correct as

necessary.

3. Verify HI and LO refrigerant pressures.

4. Allow the system to operate for several minutes and then

set the temperature selector above room temperature.

Verify the fan and compressor cycle off with the

thermostat. NOTE: The blower should also stop unless

fan switch is set to the ON position.

System Heating

1. Set the thermostat's system mode to HEAT and the

temperature mode to below room temperature.

2. Verify the outdoor unit and indoor fan stop running. After

5 minutes, increase the temperature on the thermostat

to it's maximum setting.

3. Verify the outdoor unit and indoor blower energize. Feel

the air being circulated by the indoor blower and verify

that it is warmer than ambient temperature. Listen for

any unusual noises. If unusual sounds occur, determine

the source of the noise and correct as necessary.

Defrost Control Board Test Pins

• Placingajumperbetweenthetestpinsforlessthan1

second will bypass the Anti-Short Cycle Timer.

• Placingajumperbetweenthetestpinsformorethan1

second will force the unit into a defrost cycle. As soon

as the jumper is removed, the defrost cycle will end

as determined by the typical criteria.

• Verify the Status Indicator (on the control board)

against the codes listed in Table 4 to determine proper

diagnostic description.

STATUS

INDICATOR

STATUS

TYPE

DIAGNOSTIC

DESCRIPTION

Operating Status Cooling, 1st Stage

Operating Status Heating, 1st Stage

Operating Status Anti Short Cycle Timer

Operating Status Defrost

Operating Status Power on, no call for operation

Fault Pressure switch, low

Fault Pressure switch, high

Fault Temperature Sensor, Ambient

Fault Temperature Sensor, Coil

Fault Board

(FLASHING)

Input Error

Forced defrost - test short

applied longer than 11 minutes

Table 4. Defrost Control Board Status Indicators

HEAT PUMP MAINTENANCE

WARNING:

To prevent electrical shock, personal injury, or

death, disconnect all electrical power to the unit

before performing any maintenance or service.

The unit may have more than one electrical

supply.

Proper maintenance is important to achieve optimum

performance from the heat pump. The ability to properly

perform maintenance on this equipment requires certain

mechanical skills and tools. If you do not possess these

skills, contact your dealer for maintenance. Consult your

local dealer about the availability of maintenance contracts.

Routine maintenance should include the following:

• Inspectandcleanorreplaceairltersatthebeginning

of each heating and cooling season, or more frequently

if required.

• Inspecttheoutdoorcoilatthebeginningofeachcooling

season. Remove any debris. Clean the outdoor coil

and louvers as necessary using a mild detergent and

water. Rinse thoroughly with water.

• Inspecttheelectricalconnectionsfortightnessatthe

beginning of each heating and cooling season. Service

as necessary.

CAUTION:

The unit should never be operated without a

ﬁlter in the return air system. Replace disposable

ﬁlters with the same type and size.

• Donotaddadditionaloiltomotorsunequippedwith

oil tubes. The compressor is hermetically sealed at the

factory and does not require lubrication.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 23 24

Comments to this Manuals

No comments

Kelvinator JT4BE048KA Installation Guide Page 8

Comments to this Manuals