Kelvinator JS4BD030KB Installation Guide download pdf (Page 3)

AIR CONDITIONER INSTALLATION

General Information

The S4BD series air conditioner is designed only for

outdoor rooftop or ground level installations. This unit has

been tested for capacity and efﬁciency in accordance

with AHRI Standards and will provide many years of safe

and dependable comfort, providing it is properly installed

and maintained. Abuse, improper use, and/or improper

maintenance can shorten the life of the appliance and

createunsafehazards.

Toachieveoptimumperformanceandminimizeequipment

failure, it is recommended that periodic maintenance be

performed on this unit. The ability to properly perform

maintenance on this equipment requires certain

mechanical skills and tools.

Before You Install this Unit

√ The cooling load of the area to be conditioned must be

calculated and a system of the proper capacity selected.

It is recommended that the area to be conditioned be

completely insulated and vapor sealed.

√ Check the electrical supply and verify the power supply

is adequate for unit operation. The system must be wired

and provided with circuit protection in accordance with

local building codes. If there is any question concerning

the power supply, contact the local power company.

√ The indoor section (air handler, furnace, etc) should be

installed before routing the refrigerant tubing. Refer to

the indoor unit's installation instructions for installation

details.

√ All units are securely packed at the time of shipment and

upon arrival should be carefully inspected for damage

prior to installing the equipment at the job site. Verify

coil ﬁns are straight. If necessary, comb ﬁns to remove

ﬂattened or bent ﬁns. Claims for damage (apparent or

concealed) should be ﬁled immediately with the carrier.

√ Please consult your dealer for maintenance information

and availability of maintenance contracts. Please read

all instructions before installing the unit.

Locating the Air Conditioner

• Surveythejobsitetodeterminethebestlocationfor

mounting the outdoor unit.

• Theoutdoorunit shouldbe installedno closerthan

18 inches from the outside walls of the facility and in

an area free from overhead obstructions to ensure

unrestricted airﬂow through the outdoor unit.

• Sufcientclearanceforunobstructedairowthroughthe

outdoor coil must be maintained in order to achieve rated

performance. See Figure 1 for minimum clearances to

obstructions.

• Overhead obstructions (Figure 1), poorly ventilated

areas, and areas subject to accumulation of debris

should be avoided.

• Considerationshouldbegiventoavailabilityofelectric

power, service access, noise, and shade.

Packaging Removal

NOTE: To prevent damage to the tubing connections,

carefully remove the carton and user’s manual from the

equipment. Discard the shipping carton.

Ground Level

Ground level installations must be located according to

local building codes or ordinances and these requirements:

• Clearancesmustbeinaccordancewiththoseshown

in Figure 1.

• Asuitablemountingpad(Figure1)mustbeprovided

and separate from the building foundation. The pad

must be level and strong enough to support the weight

of the unit. The slab height must be a minimum of 2”

(5 cm) above grade and with adequate drainage.

Roof Mount

• Themethodofmountingshouldbedesignedsothatit

does not overload roof structures or transmit noise to

the interior of the structure. The roof must be structurally

capable of handling the weight of the unit.

• Full perimeter support is required under the unit.

Support must be made of weather resistant materials

and installed prior to unit installation.

• Thesupportmustbebuilttoraisetheunit6"above

the roof.

Figure 1. Clearance Requirements

2” Mounting Pad

24" for

Service Access

12" or 18”

See Note

12" or 18”

See Note

DO NOT

OBSTRUCT

TOP OF UNIT

NOTE: Units require full perimeter clearances.

Installer must maintain 18” between two units

or 12” between single unit and structure.

6” from Building

or Structure

48”

1 2 3 4 5 6 7 8 ... 19 20

Comments to this Manuals

No comments

Kelvinator JS4BD030KB Installation Guide Page 3

Comments to this Manuals

Related products and manuals for Split-system air conditioners Kelvinator JS4BD030KB